AG亚游集团人堅持以為人類造福、
為社會奉獻
作為企業的社會責任感。
    室內薄型鋼結構防火塗料
  • 添加時間: 17/03/24
  • 所屬分類: 防火塗料
  • 生產廠家: 山東AG亚游集团化工集團有限公司
  • 產品價格: 來電谘詢
產品詳情
產品詢盤

一、產品簡介

1、PROSPECTUS
該產品采用水性彈性樹脂作為基料的水性鋼結構防火塗料,適用於室內鋼結構表麵的防火保護,產品具有環保、耐火極限長、粘接強度高、施工方便等特點。由國家公安部消防產品合格評定中心抽樣,由國家固定滅火係統和耐火構件質量監督檢驗中心型式認可檢驗,產品格項性能指標完全達到或超過GB 14907-2002鋼結構防火塗料標準要求。 

The product is a kind of fire retardant coating for steel structure, that is based on water-borne resin emulsion. It is used in flameproof protection of the surface of the indoor steel structure. It  has the special properties like environmental, long fire resistance, high bonding strength and easy to construct. It has been sampled by China Certification Center For Fire Products Ministry of Public Security, and taken the Type Approval Survey by CNCF(China National Center for Quality Supervision and Test of Fixed-fighting Systems and Fire-resisting Building Components). All the performance indicators reache or exceed the GB14907-2002.


二、產品特性

2、PRODUCT FEATURES
粘接強度高、耐火極限長、裝飾效果好、綠色環保無汙染、施工方便。 

1)High bonding strength; 2)Long fire resistance; 3)Good decorative effect; 4) environmental; 5)Easy to construct.
三、應用領域 

3、APPLICATION FIELDS
廣泛應用於建築物及構築物室內鋼結構、建築網架的防火保護。也可以用於石油、化工、治金、電力、煤碳等工、礦、廠房鋼結構的防火保護。

It is widely applicable to the fire protection for buildings or other structures, the indoor bearing steelwork of the large steelwork workshorp and the steel grid structure. It also can be used for the steel-structure building of petroleum industry, chemical industry, metallurgical industry, electric utility and Coal industry.  
四、施工工藝 

4、CONSTRUCTION TECHNOLOGY
1、鋼結構底材要做除汙、防鏽處理,一般至少塗刷兩道優質防鏽底漆。

1) Clean the dust and the attachments on the surface of steel structure clearly. Must derust the parts which get rusty. Anticorrosive paint twice.  
2、待底漆幹透,清除防鏽漆表麵塵土、汙物後方可塗刷NB-1室內薄型鋼結構防火塗料。 

2) The NB-1 could be used when the anticorrosive paint is dry enough, and there is no dust on the surface.
3、NB-1室內薄型鋼結構防火塗料一般采用刷塗、輥塗或噴塗工藝進行施工。塗料在使用前,須充分攪拌均勻。

3) Fully stir well before used. The coating method like Spraying, roller coating, brush could be used.  
4、為保證附著力,施工時第一遍塗層厚度須≤0.3mm,待前遍塗層幹透後再塗下一道,以後每遍塗層厚度≤0.5mm,直至總厚度達到設計要求。 

4) The thickness of the coating should control in 0.3mm in the first time construct to ensure the intercoat adhesion. Then to the next coating ,each thickness should control in 0.4mm, until the total thickness is up to the standard.
5、該產品為水性塗料,施工溫度10℃以上為宜,濕度不大於85%,遇有雨、雪、霧、大風天氣或鋼材表麵有結露時,不宜施工。 

5) The temperature when the construction is going on should be above 10℃, for this product is water-borne, and the humidity should be lower than 85%. It couldn’t going on when there’s raining, snowing, misting, winding or dewing on the surface.
6、未用完的塗料應密封保存,已備再用。

6) The rest of the coating should be sealed so that next time still be useful.

  
五、塗裝用量(理論值):

DOSAGE


耐火極限

3h

2.5h

2h

1.5h

1.0h

塗層厚度

4.5mm

3.7mm

3.0mm

2.3mm

1.6mm

理論用量

5.8kg

4.8kg

3.9kg

2.95kg

1.95kg


Fire endurance

3h

2.5h

2h

1.5h

Coating thickness

4.5mm

3.7mm

3.0mm

2.2mm

Dosagekg/m²

5.8kg

4.8kg

3.9kg

1.95kg


六、注意事項 

6、ANNOUNCEMENTS
1、施工要嚴格控製產品用量,確保塗層厚度滿足要求; 
2、本產品為一般性危險品運輸; 
3、貯存於0~38℃的環境中,隔絕火種,遠離熱源,防止曝曬; 

3) Store in 0-38℃, keep away from sun and heat.
4、貯存期為12個月。

4) Storge life:12months.